91214B DATASHEET PDF

B ILB Components datasheet pdf data sheet FREE from Datasheet (data sheet) search for integrated circuits (ic), semiconductors. UMB datasheet, UMB pdf, UMB data sheet, datasheet, data sheet, pdf, UMC, Tone / Pulse Dialer. /15C. C3. C1. OSCI. OSCO. TONE. VSS. R3. R2. R1. R4. DP. XMITMUTE. VDD. MODE IN. C2. HK. (ii) Hand-free control. HFO. HFI. 1. 2. 3. 4. 5. 6. 7.

Author: Tauzilkree Moogujas
Country: Cuba
Language: English (Spanish)
Genre: Love
Published (Last): 9 May 2017
Pages: 23
PDF File Size: 12.69 Mb
ePub File Size: 15.55 Mb
ISBN: 530-6-13380-415-7
Downloads: 8058
Price: Free* [*Free Regsitration Required]
Uploader: Tojajin

This circuit switches OFF after a time of 60 seconds you can change this switch ON-Time which is discussed in detail in coming section. Each of the low 91241b high frequency groups comprise four frequencies from the various keys present on the telephone keypad; two different frequencies, one from the high frequency group and another from the low frequency group are used to produce a DTMF signal to represent the pressed key.

Or is it compulsory to use UM in the above circuit as the application example given by sebi only? When a signal is sent from the remote telephone, the telephone interface circuit comes to receive the signal. In both the cases, the column frequency Hz is the same.

Device Control Using Telephone:

IC NE timer: The monostable multivibrater produces a single pulse when a triggering pulse is applied to its triggering input. This check is performed by an external RC time constant driven by ESt. Here this system works on tone dialing mode.

This device status feedback unit uses a dual input AND gate, the output of the flip flop and the tri state buffer are to as the input. After making confirmation of current status of the device to alter the status of that device, you have to change the mode of the tri state buffer by making the control input high. Signal limiting is performed by high gain comparators provided with hysteresis to prevent detection of unwanted low-level signals and noise. These demultiplexer are ideally suited for implementing high-performance memory decoders.

  MAKALAH IMPULS DAN MOMENTUM PDF

By using this system we can control the light from a control room or by the cell phone of the marketing person. These tones are identical and unique.

By this transistor is forward biased and the output is obtained at the emitter of the transistor. This IC inverts the data on its input terminal and gives inverted output.

91214B Datasheet

This frequency comes in the audible range between 40Hz to Hz. This system is divided into two sections 1: It can also be controlled by PCO. If device is in OFF state then no beep will 91214bb heard. When a negative going pulse is applied to its triggering input at pin 2, the output of the IC goes high. This circuit is directly connected to the telephone line.

It inhibits the detection of Hz.

By this the device is switches ON. These two tones are taken from a row frequency and a column frequency. Beep tone generator unit produces a beep tone of audible frequency. Ratasheet are sent through this telephone. Some technologies like IR remote control are used for short distance applications.

UMB Datasheet(PDF) – UMC Corporation

This 5V source is connected to all ICs and relays. Sebi Active Member Jun 5, Control the light of advertising board: In this type of PBEX only 12 extensions can be used.

Local control section contains a telephone interface circuit, ring detector circuit, signal decoder circuit, device status check circuit, device controlling circuit, device status feedback circuit. In this time interval the output of the tri state buffer will be the signal at its input terminal. The filter also incorporates notches at and Hz, providing excellent dial tone rejection. It makes accurate switching, any false switching of device are not done. Before changing the state of the device we can confirm the present status of the device.

  3COM WL 550 MANUAL PDF

In the relay driver circuit resister is used to provide the necessary base current to the transistor so that it can bias properly.

This IC gets a backup from a 9V battery. When the both inputs are high that indicates that device is switched ON, then the output of the AND gate goes logic high state. This unit is constructed using a timer chip. The internal clock circuit is completed with the addition of a standard 3. Now power supply is connected and devices are also connected so that the whole section is ready for control device using a remote telephone set.

This circuit gives an acknowledgement tone after switching ON the devices to confirm the status of the device. This is a control unit through which you can control your appliances.

91214B – Tone/pulse Dialer Search –To IL91214B

You can control up to 10 devices. This feedback tone is heard only when the device is switched ON. The whole circuit except the devices is assembled in a single cabinet in which the board gets fairly fitted along with power supply unit.

If the device is already switched ON then you will hear a short duration beep tone from beep tone generator unit. Above figure shows a single D-flip-flop. Fatasheet like to share some of those here. This is a control system through which you can control your appliances.